User Tools
Sidebar
uls:testsuite:version_180:admin_settings
Table of Contents
Administrative Settings
Defining domains and sources
Test specific domains must be defined.
| domain | description |
|---|---|
| Woodlark | create this as new domain |
| ULS | use this existing domain |
Test specific sources (servers) must be defined.
Add the sources, all sources must be defined with the ip-address of the ULS stage server, all sources are mocked. Use the ip-address of your server!
| serverid | servername | domain | ip-address | secondary ip-address | accept ip-addresses |
|---|---|---|---|---|---|
| ulstest1 | testsrv11 | ULS | 10.1.2.3 | ||
| ulstest2 | testsrv12 | ULS | 10.1.2.3 | ||
| ulstest3 | testsrv21 | Woodlark |
Check that all domains and sources have been created correctly. |
Groups and Users
Define test specific groups.
Be sure to show all domains, even those freshly created by clicking 
.
| group | rights on domain “ULS” | rights on domain “Woodlark” |
|---|---|---|
| Hotliners | none | read-only |
| Systemaniacs | read-only | full rights |
| Databasics | full rights | read-only |
| AllRounder | full rights | full rights |
Use show groups to check the result.
Define test specific users. Use the username as password. Do not assign any domains or domain privileges.
| user | group “Hotliners” | group “Systemaniacs” | group “Databasics” | group “AllRounder” | admin | password never expires | |||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AmieAction |
Use show user to show the list of all users and verify all users for correct group membership. Verify especially that “TheSpyder” has full rights on both domains and can change to the admin menu. |
Every time you login as a different user, go to administration → options and enter:
| show username | [x] |
|---|
The username should appear in the upper frame below the logos after changing to the main menu.
Notification Destinations
As user “TheSpyder” use notification → edit notification destinations → Mail to add an e-mail notification destination. Use a correct e-mail address instead of “your@emailaddress”.
| type | name | address |
|---|---|---|
| ULS Test | your@emailaddress |
Assign the new defined notification destination to group “Hotliners”. Try the test link to send a test e-mail to your@emailaddress.
Use groups → group ticket targets to define ULS ticket targets, which are destination groups in the ULS internal ticket tracking (UTT) system.
| group | name | escalation 1) | remark |
|---|---|---|---|
| Databasics | UTT Databasics |
|
Access Codes
As user “TheSpyder” use the “admin menu” and select main menu → edit access and change the description of the access codes:
| name | retention time | description |
|---|---|---|
| all | 14 | general |
| adm | 90 | admin |
| sec | 366 | security |
| ulsadmlog | 90 | uls admin actions |
Settings for Auditing
As user “TheSpyder” use the “admin menu” and select main menu → system → edit system variables and verify or change the “access-code for admin-auditing” to “ulsadmlog”:
| servername for admin-auditing | testsrv11 |
|---|---|
|
access-code for admin-auditing ! storetime in days for user changeprotocol |
360 |
Special Units
As user “TheSpyder” use the “admin menu” and select main menu → system → edit units and verify or define the unit “boolean” and “{E} :car”.
| name | si-unit | si-factor | si-offset | printflag | plotstyle |
|---|---|---|---|---|---|
| boolean | boolean | 1 | 0 | [x] | impulses lc rgb 'blue' lw 3 |
| {E} :car | {E} :car | 0 | 0 | [ ] | custom |
| [] 2) | [] 3) | 1 |
0 If that unit does not exist yet and you are creating it now, you leave “si-unit” blank and change it to itself by using the appropriate drop-down box after the unit has been initially saved. uls/testsuite/version_180/admin_settings.txt · Last modified: 2014-02-27 16:00 by uls
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
 
|